No Motors, No Circuits: UC San Diego's 3D-Printed Soft Robot Hits 4.72 Meters a Second

UC San Diego engineers printed a six-legged soft robot that runs on compressed air alone, reaching 4.72 meters per second — 100 times faster than their 2022 prototype — with zero electronics.

Key Takeaways

  • UC San Diego's six-legged soft robot reached 4.72 meters per second using compressed air alone, with no motors or electronics.
  • The result is 100 times faster than the team's 2022 prototype, which moved at 4 centimeters per second.
  • The robot borrows a compound steam engine design, using two-stage air pressure chambers to power valves and legs.
  • It is 3D-printed as a single piece from one material and can run on sand, concrete, gravel and mulch, swim, and walk underwater.
  • The robot still requires a tether to an external compressed-air source, limiting current field deployment.

Researchers at UC San Diego's Jacobs School of Engineering published results on November 18, 2026, in Science Robotics describing a six-legged soft robot that runs at up to 4.72 meters per second using compressed air alone, with no motors, batteries or electronic controls of any kind. The robot, developed by postdoctoral researcher Yichen Zhai and professor Michael T. Tolley in the Bioinspired Robotics and Design Laboratory, is 3D-printed in a single piece from one soft material, according to UC San Diego Today.

The speed represents a 100-fold jump over the team's 2022 prototype, which moved at just 4 centimeters per second. The gain came from borrowing the layout of a compound steam engine: pressurized air first drives small high-pressure chambers that act as internal valves, then flows into larger low-pressure chambers that move the six legs. "Our first walking robot demonstrated what was possible, but it was too slow," Zhai said. "We hoped to overcome this limitation, and we were fortunate to find a solution to make the new robot 100 times faster." The robot can cross concrete, gravel, sand and mulch, climb stairs, swim and walk underwater, though it still requires a tether to an external compressed-air source. The work was funded by the National Science Foundation.

Why Removing Electronics Matters More Than Speed

The headline speed figure is less important than what makes it possible: a robot with no circuitry to fail. Electronics are typically the weak point of robots sent into radiation-heavy environments, strong magnetic fields, or situations involving water intrusion, all of which can disable sensors and control boards. A robot whose locomotion is entirely mechanical — governed by air pressure and chamber geometry rather than code — sidesteps that failure mode entirely. Tolley's team points to disaster response, scientific reconnaissance near high-radiation sources, and space exploration as target applications where electronics-free operation is a genuine advantage rather than a novelty.

A Different Branch of the Soft Robotics Race

Most soft robotics research, including earlier work from Harvard's octopus-inspired grippers and MIT's pneumatic crawlers, has focused on compliance and safety around humans rather than raw speed. UC San Diego's result instead targets a performance gap that has limited soft robots to slow, cautious movement unsuitable for covering ground quickly. At 4.72 meters per second, the robot approaches speeds associated with small rigid-bodied robots, while retaining the damage tolerance and manufacturing simplicity — a single continuous 3D print — that soft robotics promises.

The tether remains the clearest limitation standing between this robot and field deployment; a self-contained compressed-air supply would need to be solved before the robot could operate untethered in a disaster zone or on another planet. Even so, the result adds a credible speed benchmark to a field that has struggled to answer skeptics who argue soft robots are too slow to be practical outside the lab.

Category: Mechanical Engineering

Tags: Soft Robotics 3D Printing Pneumatic Actuation Science Robotics UC San Diego Michael Tolley

Related Articles

Frequently Asked Questions

How fast is UC San Diego's new soft robot?

It reaches a top speed of 4.72 meters per second, powered entirely by compressed air with no electronics.

Why doesn't the robot use any electronics?

It uses a two-stage pneumatic system inspired by compound steam engines, where air pressure alone operates internal valves and drives the legs, removing the need for motors or control circuits.

Who developed the robot and where was it published?

Yichen Zhai and Michael T. Tolley at UC San Diego's Jacobs School of Engineering published the work in Science Robotics on November 18, 2026.

What is the robot's main limitation?

It requires a tether connected to an external compressed-air source, so it cannot yet operate untethered in the field.

What applications could this soft robot be used for?

Researchers suggest disaster response, high-radiation scientific reconnaissance, and space exploration, where electronics are prone to failure.